Can I Set Up a Tub Myself? Considerations And Also Steps
Can I Set Up a Tub Myself? Considerations And Also Steps
Blog Article
Listed here below you will find a lot of amazing insights about Tools You Need to Install a New Bathtub .
Mounting a tub isn't specifically rocket science, however it does need strong plumbing, carpentry, as well as often, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately challenging task. If the old bathtub is readily easily accessible, the job can relocate speedily; if you have to open a wall surface to get rid of the old tub and also place the new bathtub, the task is much harder. In either situation, the task is within a residence handyman's skills, although you will need a helper to leave the old tub and set in the new one. Make sure you have qualified yourself for the task as well as fit trying it. As opposed to working with a professional to take over a halfway-completed job, it is far better to consider employing one before you begin. Chances are you may need a professional plumber to make tube connections.
This article will help you install a new bathtub in your bathroom if you have already purchased a new tub and don't need to transform the setup of your previous water supply pipelines.
Your devices and material checklist should comprise the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, turn on the faucets to drain pipes any type of water staying in the system. The process of removing the existing faucets can be fairly troublesome due to the restricted access that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a cloth prepared for the remaining water that will certainly originate from the pipes. Once the supply pipelines have been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the single faucets from transforming during this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Before going on to fit the new taps, compare the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the installing opening in the bath/basin guaranteeing that the washing machines are in location in between the tap and also the sink. Secure the faucet in position with the producer given backnut. When the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal faucet ports. The previous type needs to be connected to the tap finishes initially, tightening only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Tub
Making use of the two wooden boards under its feet, put the bathtub in the called for setting. The wood boards are practical in uniformly spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto four little factors.
The following objective is to ensure that the bath tub is leveled all round. This can be attained by checking the spirit level as well as changing the feet on the bathtub up until the level reviews level.
To install taps, fit the bottom of the outermost adaptable tap connector to the suitable supply pipeline by making a compression sign up with; after that do the same for the other tap.
Switch on the water system and also inspect all joints as well as brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as additionally check the overflow outlet as well as the typical electrical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the supplier's user's manual. Tiling as well as securing around the bath tub needs to wait till the tub has actually been utilized at the very least when as this will certainly settle it into its final position.
Getting ready for the Installment
Firstly, the supporting frame supplied with the bath needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is essential to make sure that if the tap includes a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also practical to fit a sustaining plate under the faucets unit to prevent pressure on the tub.
Fit the flexible tap adapters to the bottom of both faucets using 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you use every one of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to now be ready to be fitted in its last setting.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to split a rigid seal, causing the water to pass through the wall between the bath and also the tiling, leading to difficulties with dampness as well as possible leakages to the ceiling below.
You can choose from a range of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and can sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly fill the bathtub with water prior to sealing, to permit the activity experienced when the tub is in usage. The sealant can fracture rather very early if you do not take into consideration this movement before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently readily available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or water resistant adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that entry about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while doing a search on the search engines. Sharing is good. Helping people is fun. I praise you for your time. Come back soon.
Contact Us Now
Report this page